Tomioka Racing S55 Twin Turbo Kit for BMW F8X M2 Competition, M3, and M4
TR-TW2008 · BMW S55 · F8X platform
The Tomioka Racing S55 Twin Turbo Kit is designed for BMW F80 M3, F82/F83 M4, F87 M2 Competition and F87 M2 CS builds that need more airflow than their original turbocharger setup. The package combines twin turbochargers, an exhaust manifold and front and rear compressor intake pipes.
This guide covers vehicle fitment, the specifications listed for TR-TW2008, our development vehicle and the supporting systems to discuss with your installer and tuner.
View the TR-TW2008 S55 Twin Turbo Kit, current pricing and availability
Which BMW models does the S55 turbo kit fit?
The current TR-TW2008 product listing specifies the following S55-powered applications:
- BMW F80 M3
- BMW F82 M4
- BMW F83 M4 Convertible
- BMW F87 M2 Competition
- BMW F87 M2 CS
This kit does not fit the standard F87 M2 with the N55 engine or the G87 M2 with the S58 engine. Confirm the engine and chassis before ordering; the M2 badge alone is not enough to establish fitment.
Before scheduling installation, have your installer review the kit instructions, actuator configuration and any existing modifications that may affect fitment.
TR-TW2008 turbocharger specifications
The following specifications come from the current Tomioka Racing TR-TW2008 product listing.
| Component | Specification |
|---|---|
| Part number | TR-TW2008 |
| Configuration | Twin turbocharger kit for the BMW S55 |
| Bearing design | Dual-ceramic ball bearing |
| Compressor wheel | 47.0 mm / 58.0 mm |
| Turbine wheel | 45.6 mm / 50.0 mm |
| Turbine design | 9-blade high-flow turbine |
| Turbine housing | 10 cm² |
| Manufacturer capability rating | 800+ HP potential, dependent on the complete build; not a verified wheel-horsepower result |
What does the 800+ HP capability rating mean?
Tomioka Racing markets this kit for builds targeting 800+ HP with suitable fuel, calibration and supporting hardware. That is a capability rating, not a guarantee of output from an otherwise stock car.
The rating should not be read as a verified 800+ WHP result. This article does not yet include a completed dyno test establishing that figure. Crank horsepower and wheel horsepower must be identified separately when comparing measured results.
Fuel quality, boost and torque strategy, engine condition, fueling capacity, charge cooling, exhaust configuration and drivetrain limits all affect the result. A larger turbocharger does not establish a safe power limit for the engine or transmission.
What comes with the S55 twin turbo kit?
The current product listing includes:
- Twin turbochargers
- Exhaust manifold
- Front and rear turbo compressor intake pipes
- Oil and coolant pipes
- Gaskets and installation hardware
Actuator configuration: New wastegate actuators are not included with TR-TW2008. Transfer the factory wastegate actuators from your original turbochargers. Have your installer inspect their condition and follow the applicable setup procedure.
Check the product page for current package details, pricing and availability. Review the Tomioka Racing warranty policy for coverage and conditions.
Our 2020 BMW M2 Competition development vehicle
The development project described here uses a 2020 BMW M2 Competition with an S55 engine and manual transmission. Its purpose is to evaluate the TR turbo upgrade as part of a complete vehicle setup, rather than treating the turbochargers as an isolated change.
The recorded project configuration includes:
- Stock S55 engine and cylinder head
- TR upgraded twin turbochargers and an upgraded crank hub solution
- BMC air filter in the stock airbox
- Upgraded charge cooling, including a Tomioka intercooler and CTS heat exchangers
- F10 EU5 injectors and high-pressure fuel system support
- Bend Calibration flex fuel hardware with a CANBUS ethanol content analyzer and ID F750 fuel filter
- Armytrix exhaust components
- Stock clutch, stock low-pressure fuel pump and stock pre-throttle pressure sensor at the recorded development stage
- No methanol injection in the recorded configuration
This is a description of a development vehicle, not a prescribed parts list or proof that every retained factory component will support the final targets. Fuel pressure, sensor range, clutch capacity and torque delivery need to be evaluated during calibration.
Development targets and validation status
The existing project plan targets approximately 600 HP on pump fuel and 750 HP on E85. These remain development targets, not verified dyno results or customer guarantees. They are not presented here as measured crank or wheel horsepower.
A useful results update should identify the dyno and correction method, wheel or engine output, fuel and measured ethanol content, boost, final hardware configuration and test conditions. Until those results are available, the project targets should be kept separate from both measured performance and the kit's advertised capability rating.
Planning the supporting modifications
Start with your intended use, available fuel and a torque target agreed with your tuner. Then assess the whole vehicle. The appropriate supporting hardware depends on its condition, existing modifications and calibration strategy.
Fueling and ethanol strategy
Discuss injector capacity, high- and low-pressure fuel delivery, ethanol measurement and fuel filtration with your calibrator. Flex fuel hardware does not by itself establish that the fuel system can meet the engine's demand. The development car's retained low-pressure pump is not a recommendation to retain it on every customer build.
Charge cooling and repeatability
Review charge-air cooling, heat exchangers and the condition of the existing cooling system. Evaluate temperatures over repeated load events appropriate to the vehicle's intended use, rather than judging the setup from a single peak number.
Engine, ignition and crank hub
Establish engine health before the upgrade. Have your installer and tuner assess ignition components, spark plug selection and gap, and whether a crank hub solution is appropriate for the build. The development car uses an upgraded crank hub; that component alone is not a guarantee against engine damage.
Transmission and drivetrain
Discuss the planned torque delivery with the shop responsible for the manual clutch or DCT setup. Inspect the drivetrain and consider the vehicle's tires, brakes and suspension as part of the complete project. The stock clutch in the development configuration is not a published torque-capacity claim.
Installation and calibration
Use an installer experienced with the BMW S55 and a calibrator familiar with the supplied turbocharger and actuator configuration. Follow the kit instructions and applicable service information for installation, fluid connections, fasteners and setup.
Before high-load operation, the installer and tuner should complete the appropriate mechanical checks and calibration for the actual hardware and fuel. This article is a build-planning guide; it does not replace the installation manual or a vehicle-specific calibration.
For additional background, read why new turbocharger pre-lubrication matters and how dual ceramic ball bearing turbochargers work.
S55 turbo upgrade FAQ
Does TR-TW2008 fit the standard F87 M2?
No. The product listing specifies S55-powered vehicles. The standard F87 M2 with the N55 engine is not included.
Does it fit the M2 Competition and M2 CS?
The S55-powered F87 M2 Competition and F87 M2 CS are listed applications. The S58-powered G87 M2 is not.
Will installing the kit produce 800 wheel horsepower?
No such result is established in this article. The 800+ HP figure is the manufacturer's capability rating and depends on the complete setup. Measured wheel output requires its own documented dyno results.
Do I reuse the factory actuators?
Yes. Transfer the factory wastegate actuators from your original turbochargers; new actuators are not included. Have your installer inspect them and complete the applicable setup procedure.
Are the M2 development car's 600 HP and 750 HP figures achieved results?
They are development targets for pump fuel and E85 respectively. Verified dyno results are not included in this article.
What should I send when asking about my build?
Include the model and year, engine, transmission, current modifications, fuel availability, intended use and power goal. That gives the team a useful starting point for checking fitment and discussing supporting hardware.
Discuss your S55 build with Tomioka Racing
Explore the TR-TW2008 S55 Twin Turbo Kit or contact Tomioka Racing about your build.
Check the race/off-road use and emissions statement when planning the vehicle's configuration and intended use.
Comments